How many amps does a kegerator draw

Click Here to register. Aug 11, 1, 1, 43 Enid, OK www. I assume the satellite receiver is pretty low. Here is what I have on the other: Kegerator - No specs available, but the guy on the phone says they are usually around 8. Haven't bought yet, but range anywhere from W to W. Tell me if I have any chance here Donnyboy Lettin' the high times carry the low Nov 17, Oct 31, 26, 22, 1, You should be fine You're biggest worry will be in-rush currents on the appliances which can pull higher than stated values instantly when they kick on So three questions: 1 What do I need to be looking at when purchasing this equipment,the watts or amps?

I looked around and did not see AMPS on any specs. Watts were all over the board-some receivers were quite small watts total, but were expensive nice receviers. Some were like W per channel and quite cheap. If so, I should just plug them in one at a time after I have started the gen? Nov 23, For the purposes of what it sounds like you are doing I'd focus more on the watts side of things.

You want a generator that can do more work or watts than you need. I mean I would bring on my generator and load it in phases I need the model number to sell it! Where could I find the model number?

What is the best way to transition through the counter in a built in use? Is there a part out there? The tower is cooled, so I need a way to connect the box and the tower. I try to run it at around 4psi but seems to be too high still. Still get a lot of foam.

You might try nitrogen instead of CO2 CO2 is what puts the fizz in soft drinks. I recently bought a micro matic unit which is built into cabinetry. Still not doing the trick. Thinking I need an narrow square in-line fan to force the warm air out.

Any idea on what product or where to buy such a product? Hey just recently bought an edge star kegerator, and have a Everyone i had talked to said to crank it up to the highest setting on 6… but now our keg tastes like crap and we are experimenting with the temperature to see what the sweet spot is.. I would recommend giving our product experts a call at They will be able to get all the info they need and help walk you through the process of getting it back to pouring and serving the way it should be.

As well as give you some further tips on how to prevent it from happening in the future and other ways to get the most out of your kegerator. All three of our kegs leak when attached to the kegerator.

They are leaking where they attach to the keg. Is it possible to connect 2 of the single gauge co2 regulators that came with the setup to provide co2 at different pressures to 2 corney kegs? I recently cleaned my lines and installed a new keg. Two days later no flow at all found co2 empty 4th keg so expected. I shut c02 tank off and replaced the next morning. I have un done everything thing again cleaned lines still same issue. I have temp about degrees pressure between psi.

Is it possible the beer went bad its un drinkable. Please Help! How much clearance should I have for venting if I have a freestanding kegerator under the bar top? Looking to install a built-in style kegerator. I see that many of these on your site have a glass rail and spill tray on top. How do you build in one of these under a counter? Can you point me to install instructions for any of the built-in styles so I can get an idea of how to build the bar top and enclosing cabinet?

Can my dual tap kegerator pour the same beer? Or do i need to connect two kegs with the same beer. HI where is this make and model made? US or overseas? I have a Danby kegerator that looks like it has slots for shelving on the inside. Is there a place to purchase shelves that fit? Please advise. I have replaced my tap for my kegorator twice in the past year.

Going on my third. The pin at the base of my tap unit keeps leaking air. If I put slight pressure on the nipple and ring it stops. I must be doing something wrong in the tapping process. Any suggestions. I have tried everything so really hope someone has an answer to this problem. Im looking at the kcss. I plan on putting it under a counter, it is open all around it so cooling the kegerator wont be an issue. But would I be able to replace the tower somehow so I could run a line up to the counter and run a tap from there.

Or must I use the tower on top of the kegerator. Once I tap a keg, is it ok to shut off the co2 when not using the kegerator? Or must I keep it charged all the time? Just set up my new outdoor edgestar. Foam, foam, foam. Is it possible that the product comes with the wrong length beer line? Any help on this would be great. Already poured 6 glasses of foam! Have an Edgestar Kegerator 3 years old one day out of warranty Just today it will not cool…compressor runs but fridge is warm.

Any thoughts? I am experiencing the same issue right now. Ice built up the the expansion plate inside the unit and actually pushed it off the kegerator popping out a screw.

Removed ice, defrosted everything, got all the water out. Put the plate back on. Turned it on and it runs for like 15 seconds every couple of minutes, no chill coming from the kegerator. We've got you covered. Unique Product Selection Your one-stop shop for the unique bar products you just have to have.

Exceed Expectations Here to help. We aim to be the go-to source for all drink enthusiasts. Customer Reviews. Same Day Shipping Order before pm est. Hassle-free Returns No Restocking Fees. Logging in Remember me. Log in. Forgot password or user name? True Kegerator on a 15 amp circuit? Posts Latest Activity.

Page of 1. Filtered by:. Previous template Next. Hi all, I looked thru the FAQ before posting this question, I hope you don't mind a newbie question that I didn't see covered.

I am considering buying a True kegerator that has a 20 amp plug.